Development

Communication / 3G + GPS:

» 3G 13: TCP and UDP clients in multiple connection

This example shows how to two clients (TCP and UDP) in multiple connection mode

Required Materials

1 x Waspmote
1 x battery
1 x 3G + GPS module
1 x GPRS/3G antenna
1 x SIM card

Notes

- 3G module must be powered with a battery
- When 3G is in use, interrupts can't be used
- Only non transparent mode
- This example can be executed in Waspmote v12 and Waspmote v15

Code

/*  
 *  ----- 3G_13 - TCP and UDP clients in multiple connection ------- 
 *  
 *  Explanation: This example shows how to two clients (TCP and UDP)
 *  in multiple connection mode
 *  
 *  Copyright (C) 2016 Libelium Comunicaciones Distribuidas S.L. 
 *  http://www.libelium.com 
 *  
 *  This program is free software: you can redistribute it and/or modify 
 *  it under the terms of the GNU General Public License as published by 
 *  the Free Software Foundation, either version 3 of the License, or 
 *  (at your option) any later version. 
 *  
 *  This program is distributed in the hope that it will be useful, 
 *  but WITHOUT ANY WARRANTY; without even the implied warranty of 
 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the 
 *  GNU General Public License for more details. 
 *  
 *  You should have received a copy of the GNU General Public License 
 *  along with this program.  If not, see <http://www.gnu.org/licenses/>. 
 *  
 *  Version:           1.3
 *  Design:            David Gascón 
 *  Implementation:    Alejandro Gállego
 */

#include <Wasp3G.h>
#include <WaspFrame.h>

char test_string[]="Test string from Waspmote!\r\n";

char apn[] = "apn";
char login[] = "login";
char password[] = "password";

char IP_1[] = "IP_1";
uint16_t port_1 = 80;
char IP_2[] = "IP_2";
uint16_t port_2 = 890;

int8_t answer;

void setup()
{
    USB.println(F("**************************"));
    // 1. sets operator parameters
    _3G.set_APN(apn, login, password);
    // And shows them
    _3G.show_APN();
    USB.println(F("**************************"));
}

void loop()
{

    // setup for Serial port over USB:
    USB.ON();
    USB.println(F("USB port started..."));
    USB.println(F("**************************"));

    // 2. activates the 3G module:
    answer = _3G.ON();
    if ((answer == 1) || (answer == -3))
    {
        USB.println(F("3G module ready..."));

        // 3. sets pin code:
        USB.println(F("Setting PIN code..."));
        // **** must be substituted by the SIM code
        if (_3G.setPIN("****") == 1) 
        {
            USB.println(F("PIN code accepted"));
        }
        else
        {
            USB.println(F("PIN code incorrect"));
        }

        // 4. waits for connection to the network
        answer = _3G.check(180);    
        if (answer == 1)
        { 
            USB.println(F("3G module connected to the network..."));

            // 5. configures IP connection
            USB.print(F("Setting connection..."));
            answer = _3G.configureTCP_UDP();
            if (answer == 1)
            {
                USB.println(F("Done"));

                USB.print(F("Opening multiple connection mode..."));
                // 6. opens multiconnection mode
                answer = _3G.createSocket(MULTI_CONNECTION);
                if (answer == 1)
                {
                    USB.println(F("Done"));
                    if(_3G.getIP() == 1)
                    {
                        // if configuration is success shows the IP address
                        USB.print(F("IP address: ")); 
                        USB.println(_3G.buffer_3G);
                    }

                    // 7. open the first client
                    answer = _3G.createMultiSocket(2, IP_1, port_1);
                    if (answer == 1)
                    {
                        //************************************************
                        //             Send a ASCII frame
                        //************************************************

                        USB.println(F("Connection established")); 
                        USB.print(F("Sending a frame...")); 
                        // create new frame (ASCII)
                        frame.createFrame(ASCII,"Waspmote_Pro"); 
                        // add frame fields
                        frame.addSensor(SENSOR_STR, test_string); 
                        frame.addSensor(SENSOR_BAT, PWR.getBatteryLevel());

                        // 8. sends a frame
                        answer = _3G.sendData(2, frame.buffer, frame.length);
                        if (answer == 1) 
                        {
                            USB.println(F("Done"));
                        }
                        else if (answer == 0)
                        {
                            USB.println(F("Fail"));
                        }
                        else 
                        {
                            USB.print(F("Fail. Error code: "));
                            USB.println(answer, DEC);
                            USB.print(F("CME or IP error code: "));
                            USB.println(_3G.CME_CMS_code, DEC);
                        }
                    }                
                    else if (answer <= -4)
                    {
                        USB.print(F("Fail. Error code: "));
                        USB.println(answer, DEC);
                        USB.print(F("CME or IP error code: "));
                        USB.println(_3G.CME_CMS_code, DEC);
                    }                
                    else
                    {
                        USB.print(F("Fail. Error code: "));
                        USB.println(answer, DEC);
                    }

                    // 9. open the second client
                    answer = _3G.createMultiSocket(1, port_2);
                    if (answer == 1)
                    {
                        //************************************************
                        //             Send a ASCII frame
                        //************************************************

                        USB.println(F("Connection established")); 
                        USB.print(F("Sending a frame...")); 
                        // create new frame (ASCII)
                        frame.createFrame(ASCII,"Waspmote_Pro"); 
                        // add frame fields
                        frame.addSensor(SENSOR_STR, test_string); 
                        frame.addSensor(SENSOR_BAT, PWR.getBatteryLevel());

                        // 10. sends a frame
                        answer =  _3G.sendData(1, frame.buffer, IP_2, port_2, frame.length);
                        if (answer == 1) 
                        {
                            USB.println(F("Done"));
                        }
                        else if (answer == 0)
                        {
                            USB.println(F("Fail"));
                        }
                        else 
                        {
                            USB.print(F("Fail. Error code: "));
                            USB.println(answer, DEC);
                            USB.print(F("CME or IP error code: "));
                            USB.println(_3G.CME_CMS_code, DEC);
                        }
                    }                
                    else if (answer <= -4)
                    {
                        USB.print(F("Fail. Error code: "));
                        USB.println(answer, DEC);
                        USB.print(F("CME or IP error code: "));
                        USB.println(_3G.CME_CMS_code, DEC);
                    }                
                    else
                    {
                        USB.print(F("Fail. Error code: "));
                        USB.println(answer, DEC);
                    }

                    // 11. closes socket
                    USB.print(F("Closing TCP socket..."));  
                    answer = _3G.closeMultiSocket(2);
                    if (answer == 1)
                    {
                        USB.println(F("Done"));
                    }
                    else if (answer == 0)
                    {
                        USB.println(F("Fail. Error code: "));
                        USB.println(answer, DEC);
                    }
                    else
                    {
                        USB.println(F("Fail. Error code: "));
                        USB.println(answer, DEC);
                        USB.print(F("CME error code: "));
                        USB.println(_3G.CME_CMS_code, DEC);
                    }

                    // 12. closes socket
                    USB.print(F("Closing UDP socket..."));  
                    answer = _3G.closeMultiSocket(1);
                    if (answer == 1) 
                    {
                        USB.println(F("Done"));
                    }
                    else if (answer == 0)
                    {
                        USB.println(F("Fail. Error code: "));
                        USB.println(answer, DEC);
                    }
                    else
                    {
                        USB.println(F("Fail. Error code: "));
                        USB.println(answer, DEC);
                        USB.print(F("CME error code: "));
                        USB.println(_3G.CME_CMS_code, DEC);
                    }
                }
                else if (answer <= -3)
                {
                    USB.print(F("Connection failed. Error code: "));
                    USB.println(answer, DEC);
                    USB.print(F("CME error code: "));
                    USB.println(_3G.CME_CMS_code, DEC);
                }
                else 
                {
                    USB.print(F("Connection failed. Error code: "));
                    USB.println(answer, DEC);
                }           
            }
            else if (answer <= -10)
            {
                USB.print(F("Configuration failed. Error code: "));
                USB.println(answer, DEC);
                USB.print(F("CME error code: "));
                USB.println(_3G.CME_CMS_code, DEC);
            }
            else 
            {
                USB.print(F("Configuration failed. Error code: "));
                USB.println(answer, DEC);
            } 
        }
        else
        {
            USB.println(F("3G module cannot connect to the network..."));
        }   
    }
    else    
    {
        // Problem with the communication with the 3G module
        USB.println(F("3G module not started"));
    }

    // 13. powers off the 3G module
    _3G.OFF(); 

    USB.println(F("Sleeping..."));

    // 14. sleeps one hour
    PWR.deepSleep("00:01:00:00", RTC_OFFSET, RTC_ALM1_MODE1, ALL_OFF);

}

Output

Serial monitor in Waspmote:

H#
USB port started...
**************************
3G module ready...
Setting PIN code...
PIN code incorrect
3G module connected to the network...
Setting connection...Done
Opening multiple connection mode...Done
IP address: 10.191.36.163
Connection established
Sending a frame...Done
Connection established
Sending a frame...Done
Closing TCP socket...Done
Closing UDP socket...Done
Sleeping...

Monitoring the TCP connection in the PC (linux):

Connection from 10.191.36.163 port 55556 [tcp/*] accepted
<=>�##356897458#Waspmote_Pro#0#STR:This is a TCP test message with frame in ASCII#BAT:69#
Connection from 10.191.36.163 port 55555 [udp/*] accepted
<=>�##356897458#Waspmote_Pro#1#STR:This is a UDP test message with frame in ASCII#BAT:69#

Quick Publish: