Development

Sensors / Events Board v30:

» Ev v30 08: Water Flow (FS300A)

This example show the flow sensor works in the corresponding socket

Required Materials

1 x Waspmote
1 x Battery
1 x MiniUSB wire
1 x Events Board v30
1 x Water flow FS300A

Notes

- This example is valid only for Waspmote v15

Code

/*  
 *  --[Ev_v30_08] - Reading flow sensor 
 *  
 *  Explanation: This example show the flow sensor works in the
 *  corresponding socket
 *  
 *  Copyright (C) 2016 Libelium Comunicaciones Distribuidas S.L. 
 *  http://www.libelium.com 
 *  
 *  This program is free software: you can redistribute it and/or modify 
 *  it under the terms of the GNU General Public License as published by 
 *  the Free Software Foundation, either version 3 of the License, or 
 *  (at your option) any later version. 
 *  
 *  This program is distributed in the hope that it will be useful, 
 *  but WITHOUT ANY WARRANTY; without even the implied warranty of 
 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the 
 *  GNU General Public License for more details. 
 *  
 *  You should have received a copy of the GNU General Public License 
 *  along with this program.  If not, see <http://www.gnu.org/licenses/>. 
 *  
 *  Version:           3.1
 *  Design:            David Gascón 
 *  Implementation:    Carlos Bello
 */
 
#include <WaspSensorEvent_v30.h>

bool flag = false;

// Variable to store the read value
float value;
//Instance objects
flowClass fs300a(SENS_FLOW_FS300);


void setup()
{
  // Turn on the USB and print a start message
  USB.ON();
  USB.println(F("Start program"));

  // Turn on the sensor board
  Events.ON();

  // Enable interruptions from the board
  Events.attachInt();
}


void loop()
{
  ///////////////////////////////////////
  // 1. Read sensor
  ///////////////////////////////////////
  value = fs300a.flowReading();

  // Print the flow read value
  USB.print(F("Flow: "));
  USB.print(value);
  USB.println(F(" l/min"));

   
  ///////////////////////////////////////
  // 2. Enable/Disable Flow Sensor 
  ///////////////////////////////////////
  // NOTE: It is possible to enable/disable interruptions
  // from the flow sensor by calling the corresponding function
  USB.print(F("Change flow interruption flag each loop(): "));
  if (flag == true)
  {
    fs300a.disableFlowInt();
    USB.println(F("DISABLED"));
    flag = false;
  }  
  else
  {
    fs300a.enableFlowInt();
    USB.println(F("ENABLED"));
    flag = true;
  }


  ///////////////////////////////////////
  // 3. Go to deep sleep mode
  ///////////////////////////////////////
  USB.print(F("Enter deep sleep... "));
  PWR.deepSleep("00:00:00:10", RTC_OFFSET, RTC_ALM1_MODE1, SENSOR_ON);
  USB.ON();
  USB.println(F("Wake up!!"));


  ///////////////////////////////////////
  // 4. Check Interruption Flags
  ///////////////////////////////////////
  
  // Check interruption from RTC alarm
  if (intFlag & RTC_INT)
  {
    USB.println(F("-----------------------------"));
    USB.println(F("RTC INT captured"));
    USB.println(F("-----------------------------"));

    // clear flag
    intFlag &= ~(RTC_INT);
  }
  
  // Check interruption from Sensor Board
  if (intFlag & SENS_INT)
  {
    // Disable interruptions from the board
    Events.detachInt();
    // Load the interruption flag
    Events.loadInt();
    
    if (fs300a.getInt())
    {
      USB.println(F("-----------------------------"));
      USB.println(F("Interruption from flow sensor"));
      USB.println(F("-----------------------------"));
    }
    
    // Clean the interruption flag
    intFlag &= ~(SENS_INT);
    
    // Enable interruptions from the board
    Events.attachInt();
  }

  USB.println();
}


Output

H#
Start program
Flow: 0.0000000000 l/min
enter deep sleep
wake up

Flow: 0.0000000000 l/min
-----------------------------
RTC INT captured
-----------------------------
enter deep sleep
...

Quick Publish: