Development

General / Utils:

» UT 01: Using EEPROM

This example shows how to use the EEPROM memory of Waspmote

Required Materials

1 x Waspmote PRO
1 x Battery
1 x MiniUSB wire

Notes

WARNING: Reserved EEMPROM addresses below @1024. 'Utils.writeEEPROM' do not let the user to write below this address. Do not try to write below this address as you could over-write important configuration. Available addresses: from 1024 to 4095

Code

/*
 *  ------ [Ut_1] Waspmote Using EEPROM Example --------
 *
 *  Explanation: This example shows how to use the EEPROM memory of Waspmote
 *
 *  Copyright (C) 2012 Libelium Comunicaciones Distribuidas S.L. 
 *  http://www.libelium.com 
 *  
 *  This program is free software: you can redistribute it and/or modify 
 *  it under the terms of the GNU General Public License as published by 
 *  the Free Software Foundation, either version 3 of the License, or 
 *  (at your option) any later version. 
 *  
 *  This program is distributed in the hope that it will be useful, 
 *  but WITHOUT ANY WARRANTY; without even the implied warranty of 
 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the 
 *  GNU General Public License for more details. 
 *  
 *  You should have received a copy of the GNU General Public License 
 *  along with this program.  If not, see <http://www.gnu.org/licenses/>. 
 *  
 *  Version:           0.1 
 *  Design:            David Gascón 
 *  Implementation:    Marcos Yarza
 */

// Variables

// address in EEPROM
int address = 1024; 
// value to write
int value =10;  
int aux = 0;
 
 
void setup()
{
  // Init USB
  USB.ON();
}

void loop()
{
  // WARNING: Reserved EEMPROM addresses below @1024
  // Utils.writeEEPROM do not let the user to write 
  // below this address.
  // Do not try to write below this address as 
  // you could over-write important configuration
  // --> Available addresses: from 1024 to 4095
  
  // Writing in the EEPROM  
  Utils.writeEEPROM(address,value);
  
  // Reading the EEPROM
  aux = Utils.readEEPROM(address);
  USB.print(F("Address EEPROM:  "));
  USB.print(address,DEC);
  USB.print(F(" -- Value: "));
  USB.println(aux,DEC);
  
  address++;
  value++;
  
  if(address == 4096) // there are 4 kB available
  {
    address = 1024;
    USB.println("END");
    delay(10000);    
  }
  delay(1);
}

Output

B#
Address EEPROM: 1024 -- Value: 10
Address EEPROM: 1025 -- Value: 11
Address EEPROM: 1026 -- Value: 12
Address EEPROM: 1027 -- Value: 13
Address EEPROM: 1028 -- Value: 14
Address EEPROM: 1029 -- Value: 15
Address EEPROM: 1030 -- Value: 16
Address EEPROM: 1031 -- Value: 17
Address EEPROM: 1032 -- Value: 18
Address EEPROM: 1033 -- Value: 19
Address EEPROM: 1034 -- Value: 20
Address EEPROM: 1035 -- Value: 21
Address EEPROM: 1036 -- Value: 22
Address EEPROM: 1037 -- Value: 23
Address EEPROM: 1038 -- Value: 24
...

Quick Publish: