Communication WaspMote and Meshlium

ghorbel · **Joined:** Mon Dec 12, 2011 1:20 pm **Posts:** 27

Hi
I'm new in meshlium and i juste buy it, so now, i want to connect 3 waspmote with meshlium and see the : Mac of XBee (802.15.4), x, y ,z , Temp, Batt level and store this information in meshlium.
My problem is how to connect the 3 waspmote with meshlium and communicate together???????

( because after that, i want to use GPS module and get langitude, latitude,... and stroring this information in meshlium and access to it the time what i want...).

So please how can i do it
please i need your help

Best Regard
Ghorbel

libelium-dev · **Joined:** Mon Sep 28, 2009 1:06 pm **Posts:** 7501

Dear ghorbel, Meshlium steore all frames sent by one or more waspmotes and you can identify by stored XBee mac address.

ghorbel · **Joined:** Mon Dec 12, 2011 1:20 pm **Posts:** 27

Hi
Thank you for the reply...

Can you please give me the steps that i can communicate waspmote and Mesh together...

because, i have connected 2 mote and i can't see any think...

Regard

libelium-dev · **Joined:** Mon Sep 28, 2009 1:06 pm **Posts:** 7501

Hello ghorbel, you only must confire the xbee and put the meshlium Xbee mac as destination, and all frames should arrive to meshlium.

Fist you can tru with a xbee gategay connected to a computer to test if it works well.

ghorbel · **Joined:** Mon Dec 12, 2011 1:20 pm **Posts:** 27

Hi libelium-dev

thanks for the reply and happy new year...

i have a new problem that when i use the command : shutdown secure by Putty SSH, after 5 min , i can't see the Meshlium network ...

what's the problem....???

please tell me what can i do to see my meshlium network??????

please help me.

Regard
ghorbel

ghorbel · **Joined:** Mon Dec 12, 2011 1:20 pm **Posts:** 27

Hi libelium-dev

Thanks to the reply...
My problem is when i want to finish using my Meshlium and after that use it, i see the command shuttdown secure in Putty SSH, i do it, but after some time , my meshlium doesn't start, so i can't see the Meshlium Network...

Yes, it's me switching Meshlium off by doing that... (for reason to make him sleeping and after that i use it...)

Please, how can i do now the see the meshlium network????

Regard
ghorbel

libelium-dev · **Joined:** Mon Sep 28, 2009 1:06 pm **Posts:** 7501

Dear ghorbel

shutdown-secure command power off the meshlium, to start it again you must disconnect the network from meshlium and connect it again.

If you have done these please follow the Meshlium Check list:http://www.libelium.com/forum/viewtopic.php?f=5&t=7710 and tell us the results

ghorbel · **Joined:** Mon Dec 12, 2011 1:20 pm **Posts:** 27

Hi libelium-dev
Thank you for the reply...

Untel now, i can't see the meshlium network...

What's the problem?? and how to resolve it?

Regard
ghorbel

libelium-dev · **Joined:** Mon Sep 28, 2009 1:06 pm **Posts:** 7501

Hi ghorbel, can you connect the meshlium to a computer by a cross-over cable or swith? (steps 2,3 and 4 of our MEshlium Checklist : http://www.libelium.com/forum/viewtopic.php?f=5&t=7710)

ghorbel · **Joined:** Mon Dec 12, 2011 1:20 pm **Posts:** 27

Hi libelium-dev

I do all the operation in URL://......7710 but no network

i see: No identifiyer Network
Can't access to the network

Regard
ghorbel