Development v12

Warning - Product Update

All the resources present on this section belong to Waspmote v12, Waspmote Plug & Sense! v12 and Meshlium v3.8.

If you have a Waspmote v15, Waspmote Plug & Sense! v15 or Meshlium v4.0 please go to the new Development Section.

Check what is your version and what are the differences between the old and the new one in this document.

Examples:

Communication / DigiMesh

» DM 01: Configure XBee

Last edition: Jan 10th, 2017 | Categories: Communication, DigiMesh

This program shows how to configure basic XBee parameters in order to communicate between different XBee devices using the same network.

» DM 02: Send packets

Last edition: Jan 10th, 2017 | Categories: Communication, DigiMesh

This program shows how to send packets to a gateway indicating the MAC address of the receiving XBee module

» DM 04a: Send broadcast

Last edition: Jan 10th, 2017 | Categories: Communication, DigiMesh

This program shows how to send packets with XBee-Digimesh modules. Broadcast address (0x000000000000FFFF) is specified as destination address

» DM 04b: Receive broadcast

Last edition: Jan 10th, 2017 | Categories: Communication, DigiMesh

This program shows how to receive packets with XBee-Digimesh modules. The packets received were broadcast

» DM 05: Get RSSI

Last edition: Jan 10th, 2017 | Categories: Communication, DigiMesh

This program shows how to get RSSI value from the last received packet. For this protocol, there is an API function which shows this information. Before running this example, make sure there is another emitter sending packets to this XBee module in order to receive information.

» DM 06a: Expansion board TX

Last edition: Jan 10th, 2017 | Categories: Communication, DigiMesh

This example shows how to use two XBee modules simultaneously in Waspmote using the Expansion board. Two different objects are created in this code, each one is used for each module. One is connected in the standard socket (SOCKET0) and the other one is connected to the Expansion board (SOCKET1)

» DM 07: Set low power mode

Last edition: Jan 10th, 2017 | Categories: Communication, DigiMesh

This program shows how to set a low power state in XBee-Digimesh: * SM=0: Normal Mode * SM=1: Asynchronous Pin Sleep Mode

» DM 08a: Complete example TX

Last edition: Jan 10th, 2017 | Categories: Communication, DigiMesh

This is a complete example for XBee-Digimesh. This example shows how to send a packet using unicast 64-bit destination address. After sending the packet, Waspmote waits for the response of the receiver and prints all available information

» DM 08b: Complete example RX

Last edition: Jan 10th, 2017 | Categories: Communication, DigiMesh

This is a complete example for XBee Digimesh. This example shows how to receive a packet. When the source address is the expected one, an answer is sent back to the emitter Waspmote

» DM 09: Set cyclic sleep mode

Last edition: Jan 10th, 2017 | Categories: Communication, DigiMesh

This program shows how to set the cyclic sleep mode in XBee-Digimesh modules. Waspmote sleeps and wakes up as XBee module commands. In order to coordinate a whole sleeping network it is recommended to switch on a network coordinator which SM parameter must be set to '7' and its SO parameter must be set to '1' so as to be a coordinator. Sleeping times are set by the user within the code but they can be modified by the network coordinator.

» DM 10: Scan network

Last edition: Jan 10th, 2017 | Categories: Communication, DigiMesh

This program shows how to scan the XBee's network in order to find other XBee modules. This example prints all available data within the API structures

» DM 11: Node search

Last edition: Jan 10th, 2017 | Categories: Communication, DigiMesh

This program shows how to search for a specific node inside the XBee's network. Once the node has been found a packet is sent to this node.

» DM 11a: Node search TX

Last edition: Jan 10th, 2017 | Categories: Communication, DigiMesh

This program shows how to search for a specific node inside the XBee's network. Once the node has been found a packet is sent to this node.

» DM 11b: Node search RX

Last edition: Jan 10th, 2017 | Categories: Communication, DigiMesh

Explanation: This program shows how to set the node identifier. Once the node has been configured is ready to receive.

» DM 13: Set/Read Power Level

Last edition: Jan 10th, 2017 | Categories: Communication, DigiMesh

This program shows how to set and read the power mode at which the XBee module transmits at. Parameter Range: 0 - 4(default)