Development v12

Warning - Product Update

All the resources present on this section belong to Waspmote v12, Waspmote Plug & Sense! v12 and Meshlium v3.8.

If you have a Waspmote v15, Waspmote Plug & Sense! v15 or Meshlium v4.0 please go to the new Development Section.

Check what is your version and what are the differences between the old and the new one in this document.

» 3G 06: Making a call

This example shows how to make a call, with a duration of 20 seconds, every 30 seconds.

Required Materials

1 x Waspmote
1 x battery
1 x 3G + GPS module
1 x GPRS/3G antenna
1 x SIM card

Notes

- 3G module must be powered with a battery
- When 3G is in use, interrupts can't be used
- This exampe can be executed in Waspmote v12 and Waspmote v15

Code

/*  
 *  -----------  3G_06 - Making call  ------------ 
 *  
 *  Explanation: This example shows how to make a  call,
 *  with a duration of 20 seconds.
 *  
 *  Copyright (C) 2014 Libelium Comunicaciones Distribuidas S.L. 
 *  http://www.libelium.com 
 *  
 *  This program is free software: you can redistribute it and/or modify 
 *  it under the terms of the GNU General Public License as published by 
 *  the Free Software Foundation, either version 3 of the License, or 
 *  (at your option) any later version. 
 *  
 *  This program is distributed in the hope that it will be useful, 
 *  but WITHOUT ANY WARRANTY; without even the implied warranty of 
 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the 
 *  GNU General Public License for more details. 
 *  
 *  You should have received a copy of the GNU General Public License 
 *  along with this program.  If not, see <http://www.gnu.org/licenses/>. 
 *  
 *  Version:           1.1
 *  Design:            David Gascón 
 *  Implementation:    Alejandro Gállego
 */

#include "Wasp3G.h"

int8_t answer;

void setup()
{
    // Setup for Serial port over USB:
    USB.ON();
    USB.println("USB port started...");

    // 1. activates the 3G module:
    answer = _3G.ON();
    if ((answer == 1) || (answer == -3))
    {
        USB.println(F("3G module ready..."));

        // 2. sets pin code
        USB.println(F("Setting PIN code..."));
        // **** must be substituted by the SIM code
        if (_3G.setPIN("****") == 1) 
        {
            USB.println(F("PIN code accepted"));
        }
        else
        {
            USB.println(F("PIN code incorrect"));
        }

        // 3. waits for connection to the network
        answer = _3G.check(180);    
        if (answer == 1)
        { 
            USB.println(F("3G module connected to the network..."));
            USB.println("Making a call...");

            // ********* must be substituted by the phone number
            // 4. makes a call
            if ( _3G.makeCall("*********") == 1)
            {
                USB.println(F("done"));
                delay(20000); // waits 20 seconds and then hang up the call
                _3G.hangUp();        
            }
            else
            {
                USB.println(F("Error making the call"));
            }
        }
        else
        {
            USB.println(F("3G module cannot connect to the network..."));
        }
    }
    else
    {   
        // Problem with the communication with the 3G module
        USB.println(F("3G module not started"));
    }

    // 5. powers off the 3G module
    _3G.OFF();

}

void loop()
{

}

Output

H#
USB port started...
3G module ready...
Setting PIN code...
PIN code accepted
3G module connected to the network...
Making a call...Done

Quick Publish: