Development v12

Warning - Product Update

All the resources present on this section belong to Waspmote v12, Waspmote Plug & Sense! v12 and Meshlium v3.8.

If you have a Waspmote v15, Waspmote Plug & Sense! v15 or Meshlium v4.0 please go to the new Development Section.

Check what is your version and what are the differences between the old and the new one in this document.

» Ga 12: NH3 Sensor on Socket3

In this example the Gases 2.0 board is turned on, reading the NH3 sensor placed on socket3 every second while printing the output voltage and sensor resistance through the USB.

Required Materials

1 x Waspmote
1 x Battery
1 x Gases 2.0 board
1 x NH3 sensor (TGS2444)

Notes

* Remember to connect the battery to Waspmote for proper operation.
* The connection of the sensor is described in the Gases 2.0 technical guide.
* The sensor gain and load resistor have been adjusted to operate with a given unit of a TGS2444 sensor, they will depend on the sensor used and the application, for more information about how to select this parameters take a look at the Gases 2.0 board technical guide.
* This example can only be executed in Waspmote v12

Code

/*  
 *  ------ [Ga_12] - NH3 sensor Reading for Gases v20-------- 
 *  
 *  Explanation: Turn on the Gases Board v20 and reads the NH3 sensor
 *  placed on socket 3 every second, printing the result
 *  through the USB
 *  
 *  Copyright (C) 2012 Libelium Comunicaciones Distribuidas S.L. 
 *  http://www.libelium.com 
 *  
 *  This program is free software: you can redistribute it and/or modify 
 *  it under the terms of the GNU General Public License as published by 
 *  the Free Software Foundation, either version 3 of the License, or 
 *  (at your option) any later version. 
 *  
 *  This program is distributed in the hope that it will be useful, 
 *  but WITHOUT ANY WARRANTY; without even the implied warranty of 
 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the 
 *  GNU General Public License for more details. 
 *  
 *  You should have received a copy of the GNU General Public License 
 *  along with this program.  If not, see <http://www.gnu.org/licenses/>. 
 *  
 *  Version:           0.1 
 *  Design:            David Gascón 
 *  Implementation:    
 */

#include <WaspSensorGas_v20.h>

#define GAIN  1      // GAIN of the sensor stage
#define RESISTOR 10  // LOAD RESISTOR of the sensor stage

// Variable to store the read NH3 value
float nh3Val;

void setup()
{
  // Turn on the USB and print a start message
  USB.ON();
  USB.println(F("start"));
  delay(100);

  // Turn on the sensor board
  SensorGasv20.ON();

  // Turn on the RTC
  RTC.ON();

  // Configure the NH3 sensor on socket 3
  SensorGasv20.configureSensor(SENS_SOCKET3NH3, GAIN, RESISTOR);
  
}
 
void loop()
{
  
  // Read the sensor 
  nh3Val = SensorGasv20.readValue(SENS_SOCKET3NH3);
  
  // Print the result through the USB
  USB.print(F("NH3: "));
  USB.print(nh3Val);
  USB.print(F("V - "));
  
  // Conversion from voltage into kiloohms  
  nh3Val = SensorGasv20.calculateResistance(SENS_SOCKET3NH3, nh3Val, GAIN, RESISTOR);
  USB.print(nh3Val);
  USB.println(F("kohms"));
  
  
  delay(1000);
}

Output

B#
start
NH3: 0.9290322303V - 51.6503639221kohms
NH3: 0.9096774101V - 52.9678802490kohms
NH3: 0.9290322303V - 51.6503639221kohms
NH3: 0.9064516067V - 53.1929321289kohms

Quick Publish: