Development v12

Warning - Product Update

All the resources present on this section belong to Waspmote v12, Waspmote Plug & Sense! v12 and Meshlium v3.8.

If you have a Waspmote v15, Waspmote Plug & Sense! v15 or Meshlium v4.0 please go to the new Development Section.

Check what is your version and what are the differences between the old and the new one in this document.

» SX 02b: RX

This example shows how to configure the SX1272 module in LoRa mode and then receive packets with plain-text payloads

Required Materials

1 x Waspmote PRO
1 x Battery
1 x MiniUSB wire
1 x SX1272 module (LoRa)
1 x Sender module with SX_02a example

Notes

- The SX1272 module is provided with a special 4.5 dBi antenna, which enables maximum range. The only exception is Smart Parking; in this case the antenna is smaller, 0 dBi, to fit inside the enclosure.
- It is not recommended to work without an antenna screwed to the module. The module could be damaged due to RF reflections.
- The SX1272 module can only be used in special Waspmote units which have been modified to drive the SPI pins to SOCKET0. (only SOCKET0 is available for SX1272)
- This module does not save the configuration. So, the network settings as the mode or the channel MUST be configured every time it is switched on.
- This example can be executed in Waspmote v12 and Waspmote v15

Code

/*  
 *  ------ [SX_02b] - RX LoRa -------- 
 *  
 *  Explanation: This example shows how to configure the semtech 
 *  module in LoRa mode and then receive packets with plain-text payloads
 *  
 *  Copyright (C) 2014 Libelium Comunicaciones Distribuidas S.L. 
 *  http://www.libelium.com 
 *  
 *  This program is free software: you can redistribute it and/or modify  
 *  it under the terms of the GNU General Public License as published by  
 *  the Free Software Foundation, either version 3 of the License, or  
 *  (at your option) any later version.  
 *   
 *  This program is distributed in the hope that it will be useful,  
 *  but WITHOUT ANY WARRANTY; without even the implied warranty of  
 *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the  
 *  GNU General Public License for more details.  
 *   
 *  You should have received a copy of the GNU General Public License  
 *  along with this program.  If not, see <http://www.gnu.org/licenses/>.  
 *  
 *  Version:           0.1
 *  Design:            David Gascón 
 *  Implementation:    Covadonga Albiñana, Yuri Carmona
 */

// Include this library for transmit with sx1272
#include <WaspSX1272.h>

// status variable
int8_t e;


void setup() 
{
  // Init USB port
  USB.ON();
  USB.println(F("SX_02b example"));
  USB.println(F("Semtech SX1272 module RX in LoRa"));

  USB.println(F("----------------------------------------"));
  USB.println(F("Setting configuration:")); 
  USB.println(F("----------------------------------------"));

  // Init sx1272 module
  sx1272.ON();

  // Select frequency channel
  e = sx1272.setChannel(CH_10_868);  
  USB.print(F("Setting Channel CH_10_868.\t state ")); 
  USB.println(e);

  // Select implicit (off) or explicit (on) header mode
  e = sx1272.setHeaderON();
  USB.print(F("Setting Header ON.\t\t state ")); 
  USB.println(e);

  // Select mode: from 1 to 10
  e = sx1272.setMode(1);
  USB.print(F("Setting Mode '1'.\t\t state "));
  USB.println(e);  

  // Select CRC on or off
  e = sx1272.setCRC_ON();
  USB.print(F("Setting CRC ON.\t\t\t state ")); 
  USB.println(e);  

  // Select output power (Max, High or Low)
  e = sx1272.setPower('L');
  USB.print(F("Setting Power to 'L'.\t\t state ")); 
  USB.println(e);  

  // Select the node address value: from 2 to 255
  e = sx1272.setNodeAddress(8);
  USB.print(F("Setting Node Address to '8'.\t state "));
  USB.println(e); 

  delay(1000);  

  USB.println(F("----------------------------------------"));
  USB.println(F("Receiving:")); 
  USB.println(F("----------------------------------------"));
}


void loop()
{
  // receive packet
  e = sx1272.receivePacketTimeout(10000);

  // check rx status
  if( e == 0 )
  {
    USB.println(F("\nShow packet received: "));

    // show packet received
    sx1272.showReceivedPacket();

  }
  else
  {
    USB.print(F("\nReceiving packet TIMEOUT, state "));
    USB.println(e, DEC);  
  }


}




Output

H#
SX_02b example
Semtech SX1272 module RX in LoRa
----------------------------------------
Setting configuration:
----------------------------------------
Setting Channel CH_10_868. state 0
Setting Header ON. state 0
Setting Mode '1'. state 0
Setting CRC ON. state 0
Setting Power to 'L'. state 0
Setting Node Address to '8'. state 0
----------------------------------------
Receiving:
----------------------------------------

Show packet received:
==============================
dest: 8
src: 2
packnum: 37
length: 26
retry: 0
payload (HEX): 546869735F69735F615F6E65775F6D657373616765
payload (string): This_is_a_new_message
==============================

Show packet received:
==============================
dest: 8
src: 2
packnum: 38
length: 26
retry: 0
payload (HEX): 546869735F69735F615F6E65775F6D657373616765
payload (string): This_is_a_new_message
==============================
...

Quick Publish: