Smar Agri - anemometer showing 0km/h

Questions about the Waspmote board and its modules
Post Reply
michellefitz
Posts: 44
Joined: Mon Aug 08, 2016 1:49 pm

Smar Agri - anemometer showing 0km/h

Post by michellefitz » Tue Sep 10, 2019 6:19 pm

Hi,

Using the smart agri example --[Ag_12] -
our anemometer is reading 0km/h - the following shows the output - vane and pluviometer seem to read correctly.

===============================
+++ RTC interruption +++
Time:Sat, 01/08/17, 22:49:10
------------- Measurement process ------------------
Current hour accumulated rainfall (mm/h): 1.9557999610
Previous hour accumulated rainfall (mm/h): 0.0000000000
Last 24h accumulated rainfall (mm/day): 0.0000000000
Anemometer: 0.0000000000km/h
Vane: NE
----------------------------------------------------
Are there any checks I can do to verify it ?

libelium-dev
Posts: 27967
Joined: Mon Sep 28, 2009 1:06 pm

Re: Smar Agri - anemometer showing 0km/h

Post by libelium-dev » Wed Sep 11, 2019 2:10 pm

Hi,

What API version did you use to upload the code to the node?

Have you tried turning the wind vane manually?

Regards

michellefitz
Posts: 44
Joined: Mon Aug 08, 2016 1:49 pm

Re: Smar Agri - anemometer showing 0km/h

Post by michellefitz » Thu Sep 12, 2019 11:13 am

Hi,

Thanks for your reply - using the following
waspmte-API-v023

This was working, but has stopped - weather vane and pluviometer prviding values, manually turning does not produce a result.

Thanks,
Michelle

libelium-dev
Posts: 27967
Joined: Mon Sep 28, 2009 1:06 pm

Re: Smar Agri - anemometer showing 0km/h

Post by libelium-dev » Thu Sep 12, 2019 3:24 pm

Hi,

Do you have Wapmote OEM or P&S? Is it v12 or v15?

Did you purchase the weather station together with the node?

Regards

michellefitz
Posts: 44
Joined: Mon Aug 08, 2016 1:49 pm

Re: Smar Agri - anemometer showing 0km/h

Post by michellefitz » Thu Sep 12, 2019 5:24 pm

Hi,

Its waspmote p&S v12 and weather station was purchased with the node.

Thanks,
Michelle

libelium-dev
Posts: 27967
Joined: Mon Sep 28, 2009 1:06 pm

Re: Smar Agri - anemometer showing 0km/h

Post by libelium-dev » Fri Sep 13, 2019 1:38 pm

Hi,
Well, in that case, it could be a damage in the wiring of the probe.

If you are able to read the vane and the pluvio, then the software is right and the Waspmote + sensor board are working as expected.

Do you see any damage on the cable? In the end, anemometer is a switch, so the electronic involved in the reading is quite simple. Do you have other nodes to test the weather station? or another weather station.

If not, please fill in the RMA form and our colleagues of the technical department will tell you the possibilities.

https://www.libelium.com/contact/#rma

Best

michellefitz
Posts: 44
Joined: Mon Aug 08, 2016 1:49 pm

Re: Smar Agri - anemometer showing 0km/h

Post by michellefitz » Mon Sep 16, 2019 12:09 pm

Hi,

no, I do see any visible damage n the cables - and we do not have any other weather station. Would it work with a smart water node ?
I will fill in the the RMA,
Thanks,
Michelle

libelium-dev
Posts: 27967
Joined: Mon Sep 28, 2009 1:06 pm

Re: Smar Agri - anemometer showing 0km/h

Post by libelium-dev » Mon Sep 16, 2019 5:12 pm

You're welcome, we already contacted through email to solve the issue.

Regards.

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest