Receiving data each 15 minutos

How to configure Meshlium or use the Manager System
Post Reply
dzabeuey
Posts: 36
Joined: Thu Aug 23, 2018 8:15 pm
Company: Ernst Young

Receiving data each 15 minutos

Post by dzabeuey » Mon Jan 14, 2019 1:34 pm

Hi,

I would like to know if its possible to change the interval that the Waspmote is getting and sending data to Meshlium. By default, i have data each 15 minutes, but i would like to change to 1 minute. Is it possible?

O change the Meshlium interval, but i understood that there is no new value to send.

Link of image example: http://ap.imagensbrasil.org/image/q7DxaU

Tks.

libelium-dev
Posts: 27967
Joined: Mon Sep 28, 2009 1:06 pm

Re: Receiving data each 15 minutos

Post by libelium-dev » Tue Jan 15, 2019 9:24 am

Hi,

You can change the sleep time of the nodes going to the configuration options through the serial monitor.

Regards

dzabeuey
Posts: 36
Joined: Thu Aug 23, 2018 8:15 pm
Company: Ernst Young

Re: Receiving data each 15 minutos

Post by dzabeuey » Tue Jan 22, 2019 11:11 am

Tks, i found it.

Now, i tried to find the same option on smart water, but i didnt find the option to this kit, is there another way?

tks.

libelium-dev
Posts: 27967
Joined: Mon Sep 28, 2009 1:06 pm

Re: Receiving data each 15 minutos

Post by libelium-dev » Wed Jan 23, 2019 8:51 am

Hi,

The configuration menu should be showed after the calibration menu. Pay attention to what is shown in the terminal. The node wait 10 seconds to enter in the menu.

Regards

dzabeuey
Posts: 36
Joined: Thu Aug 23, 2018 8:15 pm
Company: Ernst Young

Re: Receiving data each 15 minutos

Post by dzabeuey » Wed Jan 23, 2019 11:09 am

So, for this case, if i want to change the time data capture, i need to calibrate again?


Look there are no option by default:

J#
###################################
# Vertical Kit Setup #
# for Smart Water #
###################################

Using stored calibration parameters.
Press C + Enter to enter in calibration mode (timeout in 10 seconds)...

--------> Water Calibration <--------

C: Calibrate the sensors
D: Save the default values
S: Exit the calibration process (won't save values)

===========================================================

--------> Water Calibration <--------

The Smart Water node is going to be calibrated.
Step 1 of 3
Please place the following probes inside the calibration solutions:

- pH probe: pH4 calibration solution
- ORP probe: ORP calibration solution
- Dissolved Oxygen probe: in air
- Conductivity: lower μS conductivity solution

When ready, enter anything to continue

------------------------------------------------


J#
###################################
# Vertical Kit Setup #
# for Smart Water #
###################################

Using stored calibration parameters.
Press C + Enter to enter in calibration mode (timeout in 10 seconds)...

--------> Water Calibration <--------

C: Calibrate the sensors
D: Save the default values
S: Exit the calibration process (won't save values)


The calibration process ended

Start sensors and configure them
Press C + Enter to enter in configuration mode...
Finished configuration mode.
Updating RTC time from Meshlium...
Set RTC from Meshlium OK
RTC Time:Wed, 19/01/23, 10:02:23

*****************************************************
New iteration
*****************************************************
1. MEASURE SENSORS
... 1.1 Reading pH sensor...
... 1.2 Reading conductivity...
... 1.3 Reading Dissolved Oxygen Sensor...
... 1.4 Reading Oxidation-reduction potential...
... 1.5 Sensor Board OFF

... 1.6 MEASUREMENT RESULTS
... ***************************************
... temperature: 25.3546142578 degrees
... pH value: 8.1286544799
... Conductivity of the solution: 1126.6271972656 uS/cm
... DO Calculated: 57.3629493713 %
... ORP Estimated: 0.1434977054 volts
... ***************************************

2. SENDING DATA PROCESS
... 2.1 CREATING FRAME
===============================
Current BINARY Frame:
Length: 50
Frame Type: 6
frame (HEX): 3C3D3E062D1E1967057C1054A75357545F53573031230034608640D6CA4182F80E024184A97365428512D48C448310F1123E
frame (STR): <=>-g|T§SWT_SW01#

libelium-dev
Posts: 27967
Joined: Mon Sep 28, 2009 1:06 pm

Re: Receiving data each 15 minutos

Post by libelium-dev » Thu Jan 24, 2019 9:40 am

Hi,

You don't need to calibrate the sensor again if you change the time data capture.

Read the log carefully, there is a option to enter in configuration menu.
J#
###################################
# Vertical Kit Setup #
# for Smart Water #
###################################

Using stored calibration parameters.
Press C + Enter to enter in calibration mode (timeout in 10 seconds)...

--------> Water Calibration <--------

C: Calibrate the sensors
D: Save the default values
S: Exit the calibration process (won't save values)


The calibration process ended

Start sensors and configure them
Press C + Enter to enter in configuration mode...
Finished configuration mode.
Updating RTC time from Meshlium...
Set RTC from Meshlium OK
RTC Time:Wed, 19/01/23, 10:02:23
Regards

dzabeuey
Posts: 36
Joined: Thu Aug 23, 2018 8:15 pm
Company: Ernst Young

Re: Receiving data each 15 minutos

Post by dzabeuey » Thu Jan 24, 2019 1:43 pm

Sorry, i didnt see the option... i will check and return here if will be necessary

Tks

libelium-dev
Posts: 27967
Joined: Mon Sep 28, 2009 1:06 pm

Re: Receiving data each 15 minutos

Post by libelium-dev » Fri Jan 25, 2019 9:51 am

Let us know if you have any doubt.

Regards

Post Reply

Who is online

Users browsing this forum: No registered users and 1 guest